Capsel™ upgrades an insulated tumbler to a robust medication carrying case

Here's how you put the kit together for first use.

Capsel™ Kit Contents

Cap comes Pre-Assembled with these parts

  • Cap SQ1 (for Stanley® 14oz H2O Tumbler) or YB1 (for Yeti® 18oz Rambler bottle)
  • O-ring
  • Retainer SP1 (Insulating Spacer)
  • “Medication” Badge
  •  Badge Ring

Phase-Change Material (PCM) Kit contains

  • two twin packets
  • two single packets

Additional Included Items

  • Frame SQ1 or YB1
  • Tool T1

Extras

  • “Epinephrine” Badge [C-BDG-001]
  • Retainer AT1 for AirTag [C-INR-AT1] 

Capsel™ Assembly Instructions

Watch the video! But if you prefer written instructions:

Gather from home

  • If PCM packets are solid (white), then fill your tumbler with hot-to-the-touch but not scalding tap water (Around 110F)
  • Small towel

Assembly Instructions

  1. If PCM packets are solid: Place them into the tumbler of hot water. Wait 5 minutes for them to melt to clear liquid. Change water as necessary (*do not microwave packets, heat in oven, or put in water too hot to comfortably touch) and drain when melted. Dry off the packets and tumbler with the towel.
  2. Insert twin-packets (in clear liquid phase) on opposite sides inside the tumbler.
  3. Use the Frame to hold packets place, with special attention to symmetry and avoiding pinch points
  4. Insert single-packets (in clear liquid phase) through slots
  5. Use the Tool with round, wide spacer side down, and adjust packet positioning as needed
  6. Keep upright and allow PCM packets to to cool and solidify
  7. Remove Tool
  8. Insert your medications

How to Change the Badge

Needed to change the Badge

  • Capsel Tool
  • New badge
  • Capsel Cap

Badge Change Instructions

  1. Line up the two indents on the Tool’s “Badge Ring Remover” with the indents on the rim of the Badge Ring
  2. Holding firm pressure to keep the indents lined up, turn the Tool counter-clockwise to loosen the Badge Ring
  3. Remove the Badge Ring and old badge
  4. Insert the new Badge into the Badge Ring and loosely screw the Badge Ring onto the top of the Cap. Don’t worry about the alignment right now. You will tighten down the Badge Ring in the final step.
  5. Screw the assembled Cap onto the tumbler until secure. 
  6. Rotate the Badge to your preferred alignment. Hold with one hand, then use the Tool to tighten the Badge Ring until secure. Slight flex of the Badge may occur and is normal.

How to Change the Tracker Retainer

Needed to change the Tracker Retainer

  • Capsel Tool
  • New Tracker Retainer
  • Capsel Cap

Instructions

  1. Place the “Tracker Ring” side of the Tool in the two indents on the Tracker Retainer
  2. Turn counter-clockwise to loosen and remove the old Tracker Retainer
  3. Place the new Tracker Retainer and tracker
  4. Use the Tool to tighten clockwise

Cautions/Warnings

Capsel

  • Don’t use an assembled Capsel for food or drinks - Capsel is not designed for food or beverage contact. You can always remove the Capsel components and reuse your tumbler or bottle as before.
  • While Capsel is splash-resistant, it is not tested or rated for submersion
  • While Capsel provides temperature stability for medications, high temperatures should still be avoided. Capsel’s hard plastic parts may soften above 75ºC/167ºF.

Phase-Change Material Packets

  • Do not microwave, place in oven, or use other sources of direct heat. Use hot tap water to melt the PCM.
  • PCM packets contains purified paraffin wax, which is nontoxic and similar to candle wax in composition. In the rare case that a packet develops a leak, you may scrape off solid wax and wash skin with warm soapy water. Hopefully this is obvious, but the wax should not be eaten. In case of contact with eyes or mucous membranes, flush with water for 15 minutes. Seek medical attention if irritation persists.
  • In the unlikely event that you experience a leak, please contact Marimo Labs for troubleshooting and replacement.

Good to Know

Cleaning

  • Clean with a damp soft cloth.

Suitability, Warranty, and Liability

  • Capsel is in beta testing. Every effort has been made to make Capsel safe. However, not all situations can be anticipated. There are countless combinations of tumblers, bottles, and medications. You are responsible for assessing your use case for safety and effectiveness.
  • Please immediately inform Marimo Labs if you encounter any quality or safety concerns, even if they were flukes or very minor, so others can be informed and the design improved if needed.
  • Liability is limited to your purchase cost of Capsel and specifically does not cover medication, sickness, or injury.
  • By your use of Capsel, you agree to hold harmless Marimo Laboratories LLC and its owners, employees, and affiliates.
  • Capsel is not endorsed by any manufacturer of tumblers or bottles mentioned. Trademarks are used for identifying purposes and are the property of their respective owners.

Purchase Capsel™

A limited run of Capsel™ is available for purchase exclusively at the Marimo Labs Store.

Purchase Capsel™